How To Whitewash Old Stone Fireplace
After a few minutes of painting, go back with an old towel and dab where the section started. I suggest using a bucket for this, though you won’t need much to finish a whitewash well.
Please note the supplies are clickable if you want to purchase directly:
How to whitewash old stone fireplace. I simply vacuumed all of the stone on my fireplace. How to whitewash a brick fireplace: Dip your brush lightly into mixture and take off any excess.
An old towel you can throw away. Below is a list of the materials you will need for this easy diy fireplace makeover. Apply in light even strokes, blending the mixture into the stone or brick.
Make up your paint mixture. The milk paint brand and finish (as shown in my project photos) is safepaint in snow white by the old fashioned milk paint co. This project is quick, easy and completely transforms the look of your fireplace.
Push your rag with whitewash into the stone. Here are some pics for y'all. If you cannot move it, cover it.
Start painting on one of the sides of the fireplace. However, both looked really messy. Start off by cleaning your fireplace a bit.
If too much paint comes off, then paint a little longer and try again in a few minutes. 1 part white chalkboard paint; It’s all natural and environmentally friendly:
Following are the supplies i recommend to whitewash a stone fireplace. I would recommend dabbing on the stone and grout as opposed to rubbing. A bucket of water, good scrub brush, and fireplace cleaner should do the trick to remove any dust, dirt, and grime from the brick.
Pour 4 parts water in the bucket. Pour 1 part white paint in the bucket. All you need is some chalk paint (in white and light gray), water, painter's tape, a plastic tarp, and some paintbrushes!
If you want more of the stone to show through use a bit more water. While the paint is still wet follow up with your dry rag to blot any excess paint. I mixed up some whitewash (plain white flat latex paint mixed with water 50/50) and took a rag and started blotting on the whitewash.
Cover the floor with plastic and adhere it to the area around the fireplace with painters' tape. All you have to do is mix white paint and water in equal portions. Continue painting the fireplace until it is completely covered in a thin coat of the whitewash mixture.
This is what i chose to give my fireplace a makeover in just a. I thought about learning how to do a true german smear or how to whitewash a fireplace with lime. Another way to whitewash is to use concrete stain — no water needed, just concrete stain rubbed on and wiped off to your liking.
We started by brushing on the whitewash mixture onto a small stone on the lower side of the fireplace. Move furniture that is near the fireplace. I used a damp towel and wiped down the whole thing to get rid of dust, dirt and any loose junk.
Insert a wide paint brush into the whitewash solution and paint it onto the stone fireplace making sure to work the bristles around any curves and in the mortar crevices. The first step of whitewashing is to mix water with paint. When i first moved into berrybrier i knew something would need to change on the living room fireplace.
Chalked paint works best for that weathered look. I applied light, even strokes and then blended with the dry brush. Cover everything around the fireplace.
If you need to make more mixture, make sure you follow the same measurements you did the first time, so the mixture is the same over the entire fireplace. As i mentioned, i scoured pinterest for pictures of farmhouse fireplaces, and what i liked the most were those that had a german smear or a mortar wash. To make the whitewash solution for a stone fireplace , mix equal parts of the following ingredients in a plastic container to an even consistency:
Submerge just the ball you formed into the whitewash and once that is good and wet press your rag into the stone. This is actually fairly easy. You can adjust the amount of water you add depending on the effect and color you want to achieve.
It was important to me keep the look of the stone so i kept it light. Before you paint or whitewash brick or stone, remember that once done, it's difficult (if even possible) to totally undo (absent the skill of a pro and/or a real mess in your home). Number of coats will depend on the coverage you are looking for.
All you do is water down your paint (20 to 30%), and brush away. We added 1 cup of water to about 2 cups of paint and then stirred it well. I used a 50/50 mix of my paint and water.
Supplies needed to whitewash a stone fireplace. If you have thought about brightening up your brick or stone fireplace, annie sloan chalk paint is your answer! I honestly would have done even more water, but it was already really messy and wet to apply.
It was a stacked stone fireplace and clearly added onto the house in the 60s or 70s. This is where you can experiment with your mixture to see how well it covers. Brighten it up with some chalk paint to create a more modern whitewashed look.
If you have suit buildup on your fireplace i would suggest using a stone cleaner to thoroughly clean it before whitewashing. The first step will be to clean your fireplace of any dust, ashes, or suit etc. Dab your brush on a rag to remove excess mixture.
The one change the fireplace could really use is having half the height of the hearth removed. The first step to whitewashing a stone fireplace is knowing how to make a whitewash. It’s just slaked (or hydrated, meaning it’s been blended with water) powdered limestone, which dries into solid white calcite when it reacts with carbon dioxide.
The center was slightly blackened with soot and the stones were wildly different color tones, varying from yellow to red to brown. If too much red or too much brown is showing through for your taste, just rub some more whitewash on. I used a 50/50 mixture of tap water and the paint to create more of the “washed” effect so that it didn’t all look like a flat, painted surface.
It is so large it overwhelms. I could wipe off if it was too dark or add some if it was a little light. If you get too much whitewash, simply rub off what you don’t want (if it’s already dried, sand it off).
